REVO | AUDI, S4, 3.0 V6 TFSI |354ps | ECU SOFTWARE

Revo offers some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy, and engine longevity.

Revo performance ECU Software gives you much more than just an increase in power and torque. A large part of development is based on driving scenarios and feedback; our calibration doesn’t just offer great dyno curves and peak power/torque figures but an exhilarating driving experience. Expect smooth and refined response at low RPM & partial throttle, with huge gains at wide-open throttle and throughout the whole rev range.

You will find the 3.0 TFSI V6 EA839 engine nested in the Audi S4/5 B9 and SQ5. Developing around 354PS between 5400-6400rpm, and 500NM from 1370-4500rpm it has all the right ingredients, however as we know there is room for improvement. Unusually for a V6 it has a 90° block angle, rather than the more traditional 60°, with a balance shaft to compensate for the torque inertia and promote smooth running. Also, thanks to its aluminium construction it’s lighter than the previous 3.0 TFSI V6 variants.

Intensively tested and refined on our own in house S4 along alongside our Global Development Programme, throttle response has been dialled in to give the driver a deeper sense of connection and involvement with the car. Without compromising on the refinement of the driving experience, one of the main selling points of this engine and vehicle. Rather than being pulled, the hike in torque gives the feeling of a firm push from the bottom of your back, and it’s addictive, the car now begs to be driven. Optimised power delivery and with much more torque at its disposal, you can now drop below 4000rpm and still pull hard out of any corner without hesitation.

STAGE 1 ECU SOFTWARE FEATURES:

COLD START PROTECTION
RPM is limited until safe oil temperature is reached.
…
TEMPERATURE PROTECTION
Enhanced engine cooling and oil temperature management.
…
SPEED LIMIT
The top speed limit for this vehicle has been removed.

STAGE 2 ECU SOFTWARE FEATURES:

EXHAUST OVERRUN
Exhaust impulse combustion fade less through the rev range
Exhaust flaps always open in Dynamic mode
CAT heating from coldstart altered to reduce high RPM starting and excessive noise
…
LEFT FOOT BRAKING
Left foot braking has been enabled on this vehicle.
…
ADDITIONAL FEATURES
Along with all the features above the software includes the following:
Stop/start default mode changed to “off”.
Dash Boost pressure display recalculated.
Idle RPM increased in Sport mode – Improves pedal feel when accelerating from stationary, and gives a faster response and noise.
Launch control enhanced to allow peak boost at 3800rpm.

REQUIRED HARDWARE FOR STAGE 2:

Revo Performance Pack
or
Revo Intercooler
Revo Intake System
Revo Intercooler Pipe Upgrade
Turbo Back Exhaust with Sports Cat

NOTE:
Power is dependant on Fuel Quality, Performance Settings and Conditions.

Price displayed will vary depending on and discounts may apply:
– If there is any existing ECU software on your vehicle.
– If you have exisiting Revo ECU software on your vehicle and you’re going up through the stages.

REQUIRED HARDWARE FOR STAGE 2:

Revo Performance Pack
or
Revo Intercooler
Revo Intake System
Revo Intercooler Pipe Upgrade
Turbo Back Exhaust with Sports Cat

Vehicle Fitment for this product

Please be aware, this list of compatible vehicles is taken from data provided by the supplier. It is recommended, if you’re unsure, to contact us first before placing an order.

• Audi > S4 (B9 2017-present) > S4 (354ps) 2017-present
• Parts > Vehicle Tuning > Revo ECU Software

We’re providing you with an all in one, supply and fit, performance parts solution which is facilitated by our network of trusted, reputable Quattro-Tech sites across Cambridgeshire.

Any products ordered will be delivered to your chosen Quattro-Tech site at checkout for fitment.

A member of our team will be in touch with you directly, via phone or email, once you have completed your order to discuss a date and time for fitment at your chosen site location.

You will then receive an order confirmation email with the full details of your’ booking, including parts ordered, site location, date and time.

ORDER, ARRIVE AND DRIVE.

Do you have a question?

If you have a question about this product, just fill in the form below. We’ll get back in touch as soon as possible.