REVO | SKODA, OCTAVIA MK2 (2005 – 2013), 2.0 TFSI – TURBO K03 | 200ps | ECU SOFTWARE

The two-litre EA113 TFSI engine appeared in 2004 and was used in a huge range of vehicles within the Volkswagen and Audi group. Performance ECU software is a must-have for any 2.0TFSI equipped vehicle and offers great performance gains and a lot of potential for those driven to experience its true potential. We’ve specifically calibrated the software to improve the performance of the entire rev range and can be tailored to your specific requirements with our unique software adjustability.

GET FAR MORE THAN A PEAK POWER FIGURE.

Revo offers some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity.

Revo performance ECU Software gives you much more than just an increase in power and torque. A large part of development is based on driving scenarios and feedback; our calibration doesn’t just offer great dyno curves and peak power/torque figures but an exhilarating driving experience. Expect smooth and refined response at low RPM & partial throttle, with huge gains at wide-open throttle and throughout the whole rev range.

REQUIRED HARDWARE FOR STAGE 1:

Latest revision factory DV
Latest revision factory PCV

REQUIRED HARDWARE FOR STAGE 2:

Turbo Back Exhaust with High Flow Catalyst
High Flow Intake System with correct MAF scaling

RECOMMENDED HARDWARE FOR STAGE 2:

Uprated Intercooler
Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV

REQUIRED HARDWARE FOR STAGE 2+:

Turbo Back Exhaust with High Flow Catalyst
High Flow Intake System with correct MAF scaling
Uprated High Pressure Fuel Pump

RECOMMENDED HARDWARE FOR STAGE 2+:

Uprated Intercooler
Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV
Uprated Clutch

REQUIRED HARDWARE FOR STAGE 3:

Revo K04 Turbo Kit (or OEM K04 Turbo)
S3 injectors
Revo Cold Air Intake
3” Turbo Back Exhaust with High Flow Catalyst
Revo Front Mount Intercooler
Highflow Mechanical fuel pump

RECOMMENDED HARDWARE FOR STAGE 3:

Revo EngineMountKit
Uprated Clutch
Latest revision factory DV
Latest revision factory PCV

REQUIRED HARDWARE FOR STAGE 4:

3071R External Wastegate Turbo Kit with 1bar spring and associated hardware for fitting and installation
RS4 injectors
3.0″Turbo back exhaust with highflow catalytic convertor
Cold Air Intake with correctly scaled MAF housing
uprated or additional intercooler (S3 uses larger stock IC but additional IC is recommended)
highflow mechanical fuel pump upgrade
TTRS low pressure fuel pump and controller

RECOMMENDED HARDWARE FOR STAGE 4:

Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV
Uprated Brakes
NGK Iridium Spark Plugs
Uprated Clutch
Uprated Rods and Pistons required if you want to run higher boost levels and push the turbo

REQUIRED HARDWARE FOR STAGE 1:

Latest revision factory DV
Latest revision factory PCV

—

REQUIRED HARDWARE FOR STAGE 2:

Turbo Back Exhaust with High Flow Catalyst
High Flow Intake System with correct MAF scaling

RECOMMENDED HARDWARE FOR STAGE 2:

Uprated Intercooler
Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV

—

REQUIRED HARDWARE FOR STAGE 2+:

Turbo Back Exhaust with High Flow Catalyst
High Flow Intake System with correct MAF scaling
Uprated High Pressure Fuel Pump

RECOMMENDED HARDWARE FOR STAGE 2+:

Uprated Intercooler
Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV
Uprated Clutch

—

REQUIRED HARDWARE FOR STAGE 3:

Revo K04 Turbo Kit (or OEM K04 Turbo)
S3 injectors
Revo Cold Air Intake
3” Turbo Back Exhaust with High Flow Catalyst
Revo Front Mount Intercooler
Highflow Mechanical fuel pump

RECOMMENDED HARDWARE FOR STAGE 3:

Revo EngineMountKit
Uprated Clutch
Latest revision factory DV
Latest revision factory PCV

—

REQUIRED HARDWARE FOR STAGE 4:

3071R External Wastegate Turbo Kit with 1bar spring and associated hardware for fitting and installation
RS4 injectors
3.0″Turbo back exhaust with highflow catalytic convertor
Cold Air Intake with correctly scaled MAF housing
uprated or additional intercooler (S3 uses larger stock IC but additional IC is recommended)
highflow mechanical fuel pump upgrade
TTRS low pressure fuel pump and controller

RECOMMENDED HARDWARE FOR STAGE 4:

Uprated Engine Mounts
Latest revision factory DV
Latest revision factory PCV
Uprated Brakes
NGK Iridium Spark Plugs
Uprated Clutch
Uprated Rods and Pistons required if you want to run higher boost levels and push the turbo

Vehicle Fitment for this product

Please be aware, this list of compatible vehicles is taken from data provided by the supplier. It is recommended, if you’re unsure, to contact us first before placing an order.

• SKODA > Octavia MK2 (1Z 2004 – 2013) > Octavia vRS 2.0 TFSI (200ps) 2007-2013
• Parts > Vehicle Tuning > Revo ECU Software

We’re providing you with an all in one, supply and fit, performance parts solution which is facilitated by our network of trusted, reputable Quattro-Tech sites across Cambridgeshire.

Any products ordered will be delivered to your chosen Quattro-Tech site at checkout for fitment.

A member of our team will be in touch with you directly, via phone or email, once you have completed your order to discuss a date and time for fitment at your chosen site location.

You will then receive an order confirmation email with the full details of your’ booking, including parts ordered, site location, date and time.

ORDER, ARRIVE AND DRIVE.

Do you have a question?

If you have a question about this product, just fill in the form below. We’ll get back in touch as soon as possible.